Shawn
Administrator
Posts: 16,265 
|
Post by Shawn on Dec 28, 2017 18:17:40 GMT -5
I think I am going to get rid of the torch lamp in my spare room. It no longer matches with what I have in there. I will replace that with a small lamp for the dresser. And thinking of getting a corner unit and placing the Extra on there for my lettuce or flowers or whatever I want to plant. I had my Nanos in that room so I don't mind an AG in there. I just need to find a nice corner piece that the Extra will fit on and I will also get Foam Board and paint it the same color as my walls so the LED's do not fade them. Anyone using a corner rack or table? What I use now is the following but I created a streamline covering for it. But I would like something nicer for that room  |
|
|
|
Post by drbanks on Dec 28, 2017 18:35:58 GMT -5
Not really for aerogardens, but for my two 13 gallon planters, I needed something sturdy and ended up with a couple of these apparently since discontinued  |
|
Shawn
Administrator
Posts: 16,265
|
Post by Shawn on Dec 28, 2017 18:49:35 GMT -5
They are nice. but like you said not for AG's, too short.
|
|
|
|
Post by jcosmo on Dec 28, 2017 21:50:17 GMT -5
This is the table I just got for my Classic 6, Bounty, and Ultra when it arrives:  I considered placing the Sprouts on the shelves, but I have 2 cats, so for now they're going to stay on the bar behind the kitchen sink. |
|
|
|
Post by drbanks on Dec 28, 2017 23:43:02 GMT -5
Nice to have drawers for all the accessories
Sent from my SM-N950U1 using Tapatalk
|
|
Shawn
Administrator
Posts: 16,265
|
Post by Shawn on Dec 29, 2017 6:09:10 GMT -5
That is a nice table too.
|
|
Shawn
Administrator
Posts: 16,265
|
Post by Shawn on Jan 2, 2018 6:07:11 GMT -5
Everything I have looked at that will hold both units look like desks and that is not what I want. So I will continue to keep looking. I thought of a bakers rack but that wont do either.
Still on the hunt for something that would look nice and fit.
|
|
|
|
Post by cjsbabygirl313 on Jan 2, 2018 9:04:40 GMT -5
Everything I have looked at that will hold both units look like desks and that is not what I want. So I will continue to keep looking. I thought of a bakers rack but that wont do either. Still on the hunt for something that would look nice and fit. Have you considered something like a drop leaf seeing/cutting table? Mom has 2 in white that she uses for LOTS of things; has a clean look, straight lines, good height, and you can open it up if you need additional surface space.  www.joann.com/double-wall-carton-home-hobby-table/13132808.html#start=1 |
|
Shawn
Administrator
Posts: 16,265
|
Post by Shawn on Jan 2, 2018 9:09:44 GMT -5
I actually have seen them however for the space it will be used in it wont work for the actual space and decor of room. Thanks for that suggestion  This has been a pain but if I do nothing I am fine with what I have also. So darn hard to find something when you have your mind makde up of what it should look like. |
|
|
|
Post by drbanks on Jan 2, 2018 10:04:32 GMT -5
Tell me about it. I had something in mind for my big planters, and after a month, finally settled on those benches I showed above.
I never really have found anything that I'd think acceptable for Aerogardens.
|
|
MaryL
AGA Farmer
Posts: 3,532
|
Post by MaryL on Jan 2, 2018 20:42:03 GMT -5
Jeaneene thanks for posting that. I had something exactly like that on my fave list on Amazon (because I did need it for sewing) but it was listed for an astonishing $400-$500. I did not know one could get it for so much less.
Right now what I have is 2 of my tall machines on top of a wooden wine rack that I had my contractor make a wider plank top for to accommodate the two (did not need a contractor for that, unless you’re me). But I wish I could accommodate two more on the bottom instead of the wine we never seem to drink.
The other is a semi-useful, semi-inadequate magazine stacking rack with the middle shelves removed. The top is perfect, but the bottom does not let you raise the hood much without scraping the vertical supports (and your hood edges). Would be perfect 1.5” wider/deeper. Now *that* I’d pay to have made. Its vertical footprint makes it easy to find places for it.
|
|
|
|
Post by cjsbabygirl313 on Jan 2, 2018 21:11:43 GMT -5
Jeaneene thanks for posting that. I had something exactly like that on my fave list on Amazon (because I did need it for sewing) but it was listed for an astonishing $400-$500. I did not know one could get it for so much less. Right now what I have is 2 of my tall machines on top of a wooden wine rack that I had my contractor make a wider plank top for to accommodate the two (did not need a contractor for that, unless you’re me). But I wish I could accommodate two more on the bottom instead of the wine we never seem to drink. The other is a semi-useful, semi-inadequate magazine stacking rack with the middle shelves removed. The top is perfect, but the bottom does not let you raise the hood much without scraping the vertical supports (and your hood edges). Would be perfect 1.5” wider/deeper. Now *that* I’d pay to have made. Its vertical footprint makes it easy to find places for it. No problem Mary! My mom said she got hers for about $60; if you get on their text list, a lot of times you get coupons for like 50% off one item - and now the table would only be half price  |
|
Happy
AGA Bounty
Posts: 506
|
Post by Happy on Aug 7, 2018 14:11:52 GMT -5
|
|
|
|
Post by Deleted on Aug 7, 2018 17:51:17 GMT -5
Decorative and would hold 2 Bounties and a small machine
|
|
